Tascam IF-DM Uživatelský manuál

1 TEAC Professional Division OWNER’S MANUAL

10Follow the instructions given. You will need to supply your computer’s Administrator password in order to install the drivers. A License file and

111. Launch the installer and carefully follow the on-screen instructions in the Installation Wizard. 2. When presented with any Windows Logo warni

12 On the first screen of the New Hardware Wizard, select “No, not this time”. 6. Confirm that the Wizard has identified the IF-FW/DM MKII card cor

138. 9. Click “Next” 10. “Your new hardware is installed and ready to use” will appear in the lower right of the Windows desktop. 11. Your IF-FW/

14 After using the “Safely Remove Hardware” function of Windows to stop the IF-FW/DM MKII, you will see “1394: Driver Offline” reported in the mixer

15 Mixer Control Screen On both the DM-3200 and DM-4800, the IF-FW/DM MKII presents a detailed setup and status display screen as shown below. Navig

16Detailed Description CARD Status This can display one of the following: “OK”, “OK (Backup)”, “Not Ready” or “Booting …” OK The IF-FW/DM MKII is r

17Illegal FS The Mixer specified an unsupported sampling frequency. Since the IF-FW/DM MKII supports all of the sampling frequencies that the DM-

18Output This allows restricting the number of channels being sent to the computer to 16 for reduced host load, or setting the full channel count of

19Audio The IF-FW/DM MKII only presents some of its channels to the Windows XP built in audio manager. This allows you to route audio from a non-DAW

2Table of Contents INTRODUCTION ... 4 FEATURES ...

20PanelÆSounds and Audio DevicesÆSounds Tab Alternatively, divide WDM and ASIO use, e.g. using channel 31 and 32 for WDM still leaves you with 30 ch

212. Select VST Multitrack 3. Select IFFWDMmkII under the ASIO Driver pull down menu 4. If it was not already selected, a dialog will popup asking

22(Note) Sonar 6 allows you to rename each channel’s identification string that is otherwise provided by the IF-FW/DM MKII driver. (Note) If the samp

23Digital Performer The following instructions are for Digital Performer 5.1 1. Under the Setup menu, select Configure Audio System Æ Configure Har

24System Clocking Master Clock When configured with an IF-FW/DM MKII, the mixer must be the master clock relative to the computer DAW. The mixer its

25Please note that when running at these track count and sampling rates, some DAW software will hit a limit in terms of hard disk throughput before t

26IF-FW/DM MKII & DM-Mixer Routing The IF-FW/DM MKII appears to the Mixer just like any other optional I/O card except that it has 32 channels of

27DM-4800 By default, the DM-4800 puts busses 1-24 on IF-FW/DM MKII outputs 1-24 and duplicates busses 1 – 8 on outputs 25-32. These routing settin

28DM-4800 The IF-FW/DM MKII’s mixer inputs are configured from the INPUT tab of the mixer’s ROUTING screen. (Note) By default, there are no option c

29The IF-FW/DM MKII Control Panel Windows The IF-FW/DM MKII Control Panel is found here: Start Menu Æ All Programs Æ TASCAM Æ IFFWDMmkII Æ IFFWDMmkI

3MIXER OUTPUTS... 26 DM-3200 ...

30• Channel count – How many channels are currently being streamed to and from the mixer. This can be changed only from the mixer’s LCD screen. (Not

31• Enable WDM Audio – check box. Allows the WDM part of the driver to be disabled and only leave ASIO running. This may improve responsiveness of y

32These last 5 settings differ also in the names that the application sees for each channel, no additional processing is implied. These match the Win

33 Mac The IF-FW/DM MKII Control Panel is found under the Applications folder. Double click to launch it. It can also be reached through the Audio M

34the individual streams of FireWire data. All streams must be locked for audio to be sent. • Audio Dropouts – displays how many buffers have been l

35Cycle the Power Sometimes, turning off the computer and mixer at their power source and turning them back on again can solve some issues by allowin

362. Right click on My Computer, select “Properties” and left click this. 3. Select the Hardware Tab 4. Click the Device Manager 5. In the list u

37Remove unrelated software and drivers The presence of drivers for other FireWire devices and other audio devices, even though they are not actively

38Appendix Safety Boot Feature Software updates may be made available for the IF-FW/DM MKII through TASCAM’s web site (www.tascam.com). When you use

39To use it, pull it up and off of the pins and replace it onto the pair of pins nearby that are marked “J15 BACKUP”. Push it all the way down onto t

4Introduction Thank you for purchasing the TASCAM IF-FW/DM MKII FireWire audio card for TASCAM mixers. It is designed to provide audio and MIDI inte

40any power or indicator LEDs on the Hub are on if you experience problems. FireWire Active Extension cables are also hubs, just with the cable alre

41CEntrance “Universal” and “Ideal” Drivers for Windows XP. Although CEntrance (www.centrance.com) supplies 3rd party drivers that may support the DI

42Technical Specifications [Size] 164(W) x 40(H) x 221(D) mm (Card) [Weight] 0.3Kg (Card) [Supported Sample Rates] 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz

5• 1 MIDI port In and Out from the computer It also has comprehensive status monitoring in the mixer’s LCD, and a safety boot feature of its own sof

6System Requirements Macintosh • OS: Mac OS X 10.4.4 or higher • Computer: Apple Macintosh series with on-board FireWire • PowerPC G4 1GHz or gre

7DM-4800 Requirements The DM-4800 must be running V1.10 software or later to use the IF-FW/DM MKII. A TFI update file for use with TMCompanion is pro

8Installation Installing the IF-FW/DM MKII • DM-3200: The IF-FW/DM MKII must be installed in to mixer Slot 1. It will not function in Slot 2. • DM

9• Please note that the IF-FW/DM MKII must be connected by itself on a FireWire bus. More than one FireWire connector on a computer does not mean e